| A | B |
|---|---|
| holds spool of thread | spool pin |
| holds the fabric against the feed dogs as you stitch | presser foot |
| regulates the tension of the tension discs on the needle thread | tension control |
| control that allows you to stitch backward | reverse stitch control |
What holds fabric in place while you sew?
Presser foot- holds fabric in place while you sew. Presser foot lever-lifts and lowers the presser foot.
What holds fabric against feeding teeth?
vocabulary
| Question | Answer |
|---|---|
| Teeth that feeds fabric through machine | Feed dogs |
| Holds fabric against feed dogs | Presser Foot |
| Lifts and lowers the presser foot | Presser Foot Lifter |
| Carries the thread and pierces the fabric | Needle |
What holds the spool of thread?
Bobbin – The spool that sits in the lower part of the machine. It holds the thread that makes the underside of a stitch.
What holds the needle and moves up and down with each stitch?
Parts of the Sewing Machin
| A | B |
|---|---|
| Take Up Lever, | Controls amount of thread pulled from the spool to the needle for each stitch; moves up and down as you sew |
| Tenson Control | Regulates the tension placed on the needle thread by tightening or loosening the tension discs that the upper thread passes through |
What kind of machine that makes you an easier and faster?
Answer. -In addition to sewing faster, the serger makes a stronger seam than conventional sewing machines. Its system of needles and loopers forms a network of interlocking stitches that extend over the edge of the seam, which is why the serger is sometimes called an overlock machine.
What sewing tools is used to hold the fabric together temporarily?
Answer. Answer: We use pins to temporarily hold fabric pieces together before we sew a seam. We can also use pins to securely hold the sewing pattern to the fabric while we cut around the pattern.
What lowers and raises the feed dog?
Use the feed dog position switch to raise or lower the feed dogs. : The feed dogs are up and will help guide the fabric. : The feed dogs are down and will not help guide the fabric.
What is the dog feed on a sewing machine?
A set of feed dogs typically resembles two or three short, thin metal bars, crosscut with diagonal teeth, which move back and forth in slots in a sewing machine’s needle plate. Their purpose is to pull (“feed”) the fabric through the machine, in discrete steps, in-between stitches.
What is the flat spool that holds the bottom thread?
Cards
| Term Handwheel | Definition Controls the up and down movement of the needle and thread take-up lever by hand. |
|---|---|
| Term Bobbin | Definition A small, flat spool that holds the bottom thread. |
| Term Bobbin case | Definition Holds the bobbin and is located beneath the throat plate. |
What turns the sewing machine on and off?
Needle position control knob-moves the needle to different positions: center, right, and left. Leave at 1 for straight stitch. 2-5 is for width of the zig zag. Power switch- turns the sewing machine on or off.
What helps hold the thread in the right place?
Terms in this set (22)
- thread take up lever. pulls the thread from the spool in an up and down motion.
- thread guides. helps hold the thread in the right place.
- thread tension dials. regulates the tension on the top thread (spool thread)
- needle. …
- presser foot. …
- power switch. …
- reverse. …
- stitch length dial.
What allows you to manually move the needle up and down?
You can move the needle up and down by turning the wheel toward you with your hand.
What part of the sewing machine allows you to manually move the needle up and down?
The feed teeth (also called feed dogs) are what makes the fabric move along as you stop sewing. It does so by doing a rotating move up-and-down while pushing your fabric away from you. Every time the needle moves up and down, the feed teeth also do this circular motion to push your fabric just a little bit further.